That silver-gray bench in the corner of your yard isn’t ruined. It’s just waiting. At GOLDENTEAK we’ve been building and caring for Grade A teak furniture since 1996, and we’ve seen 20- and 30-year-old pieces come back looking nearly new after one good weekend of work.
Teak is full of natural oils and rubber, so the gray you see is only a thin layer on the surface. Underneath, the wood is usually as sound as the day it was made. Restoring it is mostly cleaning, a little sanding, and a decision about the finish you want.

The Short Answer
To restore old teak outdoor furniture:
- Check the condition. Gray and dirty is easy; soft or rotten wood is not.
- Clean it with mild soap or a teak cleaner and a soft brush, working with the grain. Never pressure wash.
- Let it dry for 24 to 48 hours.
- Sand lightly with 120 to 220 grit, only where the wood is rough, stained or splintered.
- Choose your finish: a teak sealer to keep it golden, or nothing at all to let it go silver again.
Most pieces take less than one weekend. The rest of this guide walks you through each step, plus how to fix black mildew spots, water rings, cracks and wobbly joints.
Can Your Teak Be Saved? Start With a 5-Minute Check
Before you buy a single brush, walk around the piece and look closely. What you find decides how much work is ahead.
| What you see | What it means | How much work |
|---|---|---|
| Even silver-gray color | Normal weathering of the surface | Easy: clean, then finish |
| Black or green spots | Mildew living on dirt and pollen | Easy to moderate: clean, maybe a teak cleaner |
| Rough, fuzzy or splintery surface | Raised grain from years of sun and rain | Moderate: clean, then sand |
| Peeling or flaking finish | An old varnish or sealer is failing | Moderate to hard: strip and sand |
| Fine cracks along the grain | Normal “checking” from drying and wetting | Usually cosmetic, leave it |
| Loose or wobbly joints | Hardware has loosened over time | Easy: tighten or replace |
| Soft, spongy or crumbling wood | Rot | Hard: that part may need replacing |
Pro Tip: Press a fingernail into the wood on the underside of a seat or the bottom of a leg, where water collects. If it sinks in easily, the wood is soft. Solid Grade A teak (made from the dense heartwood of mature trees) almost never gets to this point. Lower-grade teak and teak-look woods often do.
What You’ll Need
Nothing here is expensive, and most of it is probably already in your garage.
- Soft-bristle scrub brush (nylon, not wire)
- Bucket, warm water and mild dish soap
- Teak cleaner for heavy gray or mildew (a one-part cleaner is gentler than a two-part cleaner)
- Garden hose with a regular spray nozzle
- Sandpaper or sanding sponges in 120, 150 and 220 grit
- Clean cotton rags
- Teak sealer if you want the golden color back (skip it if you love the silver look)
- Rubber gloves, safety glasses and a dust mask
- Screwdriver or Allen key to tighten hardware
Use caution with these: pressure washers, steel wool, wire brushes and chlorine bleach. Each one can cause more damage than the weather ever did, unless used carefully. We explain why below.
How to Restore Old Teak Outdoor Furniture, Step by Step
Pick a dry, mild day in the shade. Direct sun dries cleaner on the wood before it can work, which leaves streaks.
Step 1: Prep the Piece
Remove cushions and anything stored on the furniture. Brush off loose leaves and cobwebs. Tighten any loose bolts or screws now, so the piece is steady while you scrub.
Step 2: Clean It, Gently
Wet the wood with the hose. Scrub with warm, soapy water and a soft brush, always along the grain, never across it. Rinse well.
For deep gray or stubborn spots, use a teak cleaner instead. Follow the label for how long to leave it on, and test it first on a hidden spot like the underside of a seat. Rinse thoroughly, because cleaner left in the wood can discolor it.
Pro Tip: Work on one section at a time, like a tabletop or one chair, and keep the rest wet. Dry patches next to wet ones leave tide marks.
Step 3: Let It Dry Completely
Give it 24 to 48 hours, longer in humid weather. As the wood dries, the grain often rises and feels fuzzy. That is normal, and the next step takes care of it.
Step 4: Sand Only Where It Needs It
Run your hand over every surface. Where the wood feels rough, or where a stain didn’t wash out, sand with the grain:
- Start with 120 or 150 grit on rough or stained areas only.
- Finish everything you sanded with 220 grit for a smooth, even surface.
- If the wood is smooth and just gray, you can often skip sanding entirely.
Use light pressure. Teak is dense and slow growing, so there’s no need to take off more than the thin gray layer. Over-sanding softens the crisp edges on arms and tabletops. Wipe off all dust with a dry rag when you’re done.
Step 5: Choose Your Finish
Now decide how you want the piece to look for the next few years: golden, silver, or somewhere in between. The finishing section below helps you choose. If you’re applying a sealer, wait until the wood is completely dry and dust free.
Step 6: Reassemble and Enjoy
Put the cushions back once the finish has fully cured (check the sealer label, usually 24 hours). Then step back and enjoy furniture that looks new again.
Fixing the Most Common Problems on Old Teak
Black Mildew Spots
Mildew feeds on the dirt, pollen and tree sap that collect on the surface, not on the teak itself. Scrub with a teak cleaner, or with a mild oxygen bleach (the powdered kind sold for laundry) mixed in warm water as the package directs. Rinse well. Spots that survive can usually be sanded out with 150 grit. Skip chlorine bleach: it can turn teak blotchy and pale.
Water Rings and Drink Stains
These sit in the top layer of the wood. Sand the area lightly with 220 grit, feathering out past the ring so you don’t leave a low spot, then finish the whole surface the same way so it all matches.
Dark Rust-Colored Spots
These usually come from steel wool, a metal can or steel hardware left on the wood. A teak cleaner that contains oxalic acid lifts most of them. Then rinse well and switch any steel hardware to stainless steel.
Cracks Along the Grain
Fine cracks, called checks, open and close as teak dries out and soaks up rain. They’re normal and rarely affect strength. Leave them alone. A deep split in a load-bearing part, like a chair leg, is different: glue it with an exterior wood glue and clamp it, or call us for a replacement part.
Wobbly Chairs and Tables
Tighten every bolt and screw. If a screw spins without tightening, the hole has worn out. Fill it with a wooden toothpick or dowel dipped in exterior wood glue, let it dry, and drive the screw back in. Most GOLDENTEAK furniture uses mortise and tenon joinery with dowels, so wobbly chairs are very rare. Where bolts are used, they are brass or stainless steel (if exposed to the elements) and can be tightened quickly.
Finishing: Golden, Silver or Oiled?
This is the decision that shapes your next few years of upkeep. There’s no wrong answer, and none of them is permanent.

| Finish | Look | Upkeep | Best for |
|---|---|---|---|
| Leave it natural | Turns soft silver-gray over 6 to 12 months | A wash once or twice a year | Low maintenance, coastal or rustic style |
| Teak sealer (our pick) | Keeps the warm golden-honey color | Clean and reapply about once a year | Keeping that just-bought look |
| Teak oil | Rich, dark, glossy | Reapply every few months | People who enjoy regular care |
Our recommendation: for restored furniture that lives outdoors, use a water-based teak sealer. It blocks the UV light that turns teak gray, lasts much longer than oil, and doesn’t feed mildew. Apply two thin coats with a clean rag or brush, about 30 minutes apart, and wipe off anything that doesn’t soak in.
Despite the name, most “teak oils” contain no oil from the teak tree. They’re blends of linseed or tung oil that can darken unevenly and give mildew something to feed on. If you love the oiled look, it works fine. Just plan on reapplying when it starts fading (which can happen in about 6 months with direct sun exposure).
Not sure? Leave it natural for a season. You can always clean and seal it later.
Mistakes That Make Old Teak Worse
- High-pressure washing. It blasts away the soft grain between the hard growth rings and leaves the surface permanently rough and ridged. A garden hose is all you need. If you must use a pressure washer (and some professionals do), use light pressure, a “fan” spray and stay at least 12 inches from the surface. In effect, you’re getting only slightly more pressure than a garden hose.
- Steel wool or wire brushes. Tiny steel fibers stay in the grain, rust, and leave black spots.
- Chlorine bleach. It strips the wood’s color unevenly and can weaken the fibers.
- Sanding across the grain. It leaves scratches that show through any finish.
- Sealing damp wood. Moisture trapped under a sealer causes cloudy patches and peeling. It’s also the most common cause of black mildew spots all over the teak surface. Wait the full 24 to 48 hours for the teak to dry.
- Plastic covers. They trap moisture and invite mildew. Use a breathable cover, or none at all.
For routine care once your furniture is restored, see our guide on how to clean teak outdoor furniture like a pro and our teak outdoor furniture care page.
Restore or Replace?
Restore it if the wood is solid, even if it’s gray, stained, rough or decades old. That covers the large majority of real teak furniture.
Consider replacing it if:
- The wood is soft or crumbling in more than one spot
- It turns out to be a lower-grade wood with a teak-colored stain (common in big-box patio sets)
- Frames are cracked through at the joints, not just checked on the surface
If it’s time for something new, look for furniture that will be worth restoring again in 30 years: solid Grade A teak, mortise and tenon joinery and FSC or SVLK certified wood. That’s what goes into every GOLDENTEAK piece. Browse our teak patio furniture, or read what makes Grade A teak different.

Frequently Asked Questions About Restoring Teak
How long does it take to restore teak furniture?
Most pieces take less than one weekend: a few hours to clean, one to two days to dry, then an hour or two to sand and seal. A large dining set can stretch over two weekends.
Can you restore teak furniture that is 20 or 30 years old?
Yes. Age alone doesn’t hurt teak. As long as the wood is solid, old Grade A teak cleans and sands back to a golden color just like newer pieces.
Do I have to sand teak to restore it?
Not always. If the wood is smooth and only gray, cleaning plus a sealer is often enough. Sand only where the surface is rough, splintered or stained.
Should I oil old teak after restoring it?
We recommend a water-based teak sealer instead for outdoor furniture. It lasts longer, protects against UV and doesn’t encourage mildew. Oil works, but needs reapplying every few months.
How do I keep restored teak from turning gray again?
Clean it once or twice a year and reapply sealer about once a year, or when water stops beading on the surface. Without sealer, it will turn silver-gray again within 6 to 12 months, which doesn’t harm the wood.
Can I restore teak furniture in winter?
It’s best to wait for a dry, mild day above about 50°F. Cleaners, drying and sealers all work poorly in the cold and damp.
Conclusion
Old teak is almost never finished. Clean it gently, let it dry, sand only where it needs it, and choose the finish that fits how much upkeep you want. One weekend is usually all it takes to bring back the warm, golden wood you fell in love with.
Have a piece you’re not sure about? Send a photo to [email protected] and we’ll tell you honestly whether it’s worth restoring. And when you’re ready to add to your outdoor space, explore our full range of Grade A teak outdoor furniture, built to be restored by your grandchildren.